iPhone 6 PlusIs perhaps the most strength of the mobile phone the limelight recently, I believe you also want to understand its internal design and the original iPhone 5 s will be different.This articleiPhone 6 PlusDisassembly is still from the familiar foreign media and dismantling site iFixit, not much said, we get into the business directly.
iPhone 6Plus size is as follows: 158.1 mm in length, width is 77.8 mm, and thickness of only 7.1 mm, compared to the iPhone 5 s 7.6 mm to be thinner.
First of all, the first step is to remove the pentagon screw at the bottom of the fuselage.Although this is not common screws do not recruit people like, but also good this time don’t need to heating way to unload it.
Next is to use screen will display and absorption after separating the body directly.
When confirm nothing will be damaged, we carefully turned up on the front panel, revealing the internal structure of the following.Here we see the apple redesigned the Touch line ID of the row, the entire process become very safe,iPhone 5SThe Touch on the ID easily because of the front panel with rows of chassis caused tears) separately.
With the iPhone 5 s is very similar, the iPhone 6 Plus screen ribbon cable with very solid metal bracket is fixed on the logic board.
After remove the front panel, we finally for the first time clearly see the iPhone 6 Plus the whole internal structure.The iPhone 6 Plus internal layout and iPhone 5 s is very similar, in addition to the whole contour was larger, the most obvious is a bigger battery.
The front panel Touch ID key component is to use a metal bracket.After remove the bracket, we can easily get the front shot it out.
The entire Touch ID key components and the usual adopted “modular” design concept, so it can repair the sex will be more bad, so might have to take a relatively long time to repair.
Front-facing camera hidden in the upper part of the front panel components among a lot of ribbon cable structure, including the speaker.
Next, we remove the metal plate on the front panel.As said before, apple has redesigned the Touch ID button row line, before it has to do with the iPhone 5 s on the fragile and twisted wire is a very great progress.And that apple will row line around the fuselage, in addition to improve the maintainability, if there is no other reason.So we think apple is doing on this point is very conscience.
Then we are going to remove the iPhone 6 Plus battery parts.
First of all, we removed the battery connector at the top of the metal.
Then, we found some tape down to the bottom of the battery.According to our experience, we can only have two choices: if the direction, all is well.If the wrong direction, then directly to the tragedy.Because the tape adhesive non-trace similar to the 3 m glue, can only let them when you pull right whole disconnect.
Luckily we pull the right direction, and 43 grams of battery is separated from the fuselage shell.
As rumors say, iPhone 6 Plus the rated voltage of 3.82 volts, battery capacity is 2915 mah, compared to the iPhone 5 s (1560 mah) nearly doubled, more than Galaxy S52880 mah also want a little more.
With larger capacity battery with higher power efficiency, it is no wonder that the iPhone 6 Plus although larger screen, but the battery life is much longer than the iPhone 5 s.Apple’s official data is: 3 g talk time can be up to 24 hours, can achieve 384 hours of standby time.
Then we found a haven’t seen the new gadget, it was a vibration module, at the right side of the battery, the logic board below.
We use small pry tool to pry open the vibration module, and then we found a ring in the motor vibration module seem quite fragile copper coils.
Near the upper fuselage camera module we use easily took out a pair of tweezers.
The new iSight logo on the back of the camera module for DNL43270566F MKLAB.
As with the iPhone 5 s, the iPhone 6 Plus is equipped with a 8 million – pixel rear camera, the aperture to f / 2.2.6 Plus also added two new features: an optical image stabilization (OIS) and phase Focus (Focus Pixel).
Although phase focusing technology has been applied more widely in the digital SLR, but its application in the mobile phone or the last two years.Six Plus the iPhone is not the first to pick up the technology of mobile devices, because before thatThe samsung Galaxy S5There has been carrying this feature.
Apple has always attaches great importance to for iPhone camera parts, so we use plastic lever handle with tweezers opens the module’s shell, take a look at what is inside.
Looks actually is not significantly different, but the updated new iSight camera can be aroused the interest of many independent producers.
At the bottom of the lens, we can see the camera’s sensor.And 6 Plus is optical image stabilization function, is through the lens component is nested in a tiny metal “cage”, driven by the electromagnetic coil around
Because of the gyroscope and M8 coprocessor can continue to offer the iPhone 6 Plus the motion of your hand, through these data the iPhone 6 Plus can compensate through the lens of fast moving components to targeted, so that you are in a low light or hand shake to reflect clearly sharp photos.
Then we should remove the iPhone 6 Plus the logic of the motherboard, and this thing is a few screws firmly fixed on the back cover shell.
Note that the logic board before get it, we must first solve the antenna at the back of the motherboard.
We can now take a look at the motherboard module circuit on some of the positive:
Red is the firstApple A8 APL1011 SoC + Elpida 1 GB LPDDR3 RAM (as denoted by the markings EDF8164A3PM-GD-F)
Orange is Qualcomm MDM9625M LTE Modem
Yellow is the Skyworks 77802-23 Low Band LTE PAD
Green is Avago A8020 High Band PAD
The blue one is Avago A8010 Ultra High Band PA + FBARs
Pink is at TriQuint TQF6410 EDGE, 3 g power amplifier module
Black is the company MP67B 6 – axis gyroscope and accelerometer combo
Motherboard positive other integrated circuit module are:
Red is Qualcomm QFE1000 Envelope Tracking IC
Orange is RFMD RF5159 can Antenna Switch be used Modul
Yellow is SkyWorks 77356-8 Mid – Band PAD
And then the main board on the back of the integrated circuit module:
Red is the SK Hynix H2JTDG8UD1BMS 128 Gb (16 Gb) NAND Flash
Orange is the Murata 339 s0228 WiFi Module
Yellow is Apple/Dialog 338 s1251 – AZ Power Management IC
Green is Broadcom BCM5976 touchscreen controller
Blue is NXP LPC18B1UK ARM architecture (M3 Microcontrollers (also known as the M8 Motion Coprocessor)
Pink is NXP 65 v10 NFC module + Secure Element (Most likely the contains an NXP PN544 NFC controller inside)
Black is Qualcomm WTR1625L RF Transceiver
Main board on the back of the other integrated circuit module:
Red is Qualcomm WFR1620 receive – only companion chip.
Orange is Qualcomm PM8019 power management IC
Yellow is Texas Instruments 343 s0694 touch transmitter
Green is the AMS AS3923 boosted NFC tag front end
The blue one is Cirrus Logic 338 s1201 audio codec
Then we remove the iPhone 6 Plus the only speaker.Although the speaker modular design is worthy of praise, but because of all the tags see not too clear, so the speaker manufacturers at present we still don’t know.
The next part is at the bottom of the fuselage to expand connections, including the headphone jack, Lighting interface and several of the antenna.
Another antenna, we can see many places in the shell, are everywhere.
Finally we found the power button and the volume button strip components.Since all of these components have some parts are string in a fragile line, so it seems there are some dangerous.
We are very like new button design, because the new rubber gasket around the power button is very interesting.
Similar rubber gasket is surrounded by the volume button.This represents the apple in dust waterproof on the one hand, the progress, but also improve the durability of a new generation of the iPhone.
Finally, the iPhone 6 Plus in our maintainability score obtained good grades 7 points, it is better than the iPhone 5 s too much, here’s why:
1. The iPhone 6 Plus display has can be used as the first dismantle components, completely simplify the maintenance process of the screen.
2. The iPhone 6 Plus battery is easy to dismantle, in addition to the need to use special pentagonal screwdriver and know how to remove the adhesive, but is not very difficult.
3. Touch ID button row line is redesigned, makes it will not be open in the front panel is easy to be tore off (on the iPhone 5 s will).